Role of aggregate characteristics in controlling the mechanical properties of ultra-high performance fiber-reinforced concrete

https://doi.org/10.58224/2618-7183-2026-9-5-4
Ultra-high-performance fiber-reinforced concrete (UHPFRC) is one of the most promising construction materials due to its superior mechanical properties and durability. Aggregates play an important role in the formation of the structure and properties of UHPFRC. In this study, 27 UHPFRC mixtures containing quartz and quartzite aggregates with maximum particle sizes ranging from 0.4 to 1.25 mm and volumetric aggregate content varied from 0 to 0.4 m3/m3 were investigated. The main mechanical properties of UHPFRC were determined, including compressive strength, flexural strength, and fracture energy. To describe the influence of aggregate characteristics on UHPFRC properties, two parameters were introduced: the total surface area of aggregate particles in the concrete mixture, Sagg,tot, and the relative number of contacts between aggregate particles and the steel fiber surface, Cg. Linear increase in the compressive strength of UHPFRC was observed with increasing Sagg,tot over the range of 0 –12.400 m², while mixtures containing quartzite aggregate exhibited 10-20 MPa higher compressive strength compared with quartz aggregate. Flexural strength and fracture energy also showed a linear dependence on Cg within the range of 0 ≤ Cg ≤ 1. At Cg ≥ 1, no further improvement in mechanical properties was observed. The introduction of aggregate increased the flexural properties of UHPFRC by up to 1.41 times. Simple empirical relationships were proposed to predict the mechanical properties of UHPFRC considering the type and content of aggregate. The correlation coefficients between the predicted and experimental values ranged from 0.92 to 0.95, demonstrating the high accuracy of the proposed models.
1. Bajaber M.A., Hakeem I.Y. UHPC Evolution, Development, and Utilization in Construction: A Review. Journal of Materials Research and Technology. 2021. 10. P. 1058 – 1074. DOI: 10.1016/j.jmrt.2020.12.051
2. Azmee N.M., Shafiq N. Ultra-High Performance Concrete: From Fundamental to Applications. Case Studies in Construction Materials. 2018. 8. DOI: 10.1016/j.cscm.2018.e00197
3. Yang J., Chen B., Su J., Xu G., Zhang D., Zhou J. Effects of fibers on the mechanical properties of UHPC: A review, Journal of Traffic and Transportation Engineering. 2022. 9. P. 363 – 387. DOI: 10.1016/j.jtte.2022.05.001
4. Wille K., El-Tawil S., Naaman A.E. Properties of Strain Hardening Ultra High Performance Fiber Reinforced Concrete (UHP-FRC) under Direct Tensile Loading. Cement and Concrete Composites. 2014. 48. P. 53 – 66. DOI: 10.1016/j.cemconcomp.2013.12.015
5. Wille K., Naaman A., El-Tawil S. Optimizing ultra-high-performance fiber-reinforced concrete. ACI Concrete International. 2011. 33. P. 35 – 41.
6. Yoo D.Y., Lee J.H., Yoon Y.S. Effect of fiber content on mechanical and fracture properties of ultra high performance fiber reinforced cementitious composites. Composite Structures. 2013. 106. P. 742 – 753. DOI: 10.1016/j.compstruct.2013.07.033
7. Xue J., Briseghella B., Huang F., Nuti C., Tabatabai H., Chen B. Review of Ultra-High Performance Concrete and Its Application in Bridge Engineering. Construction and Building Materials. 2020. 260. DOI: 10.1016/j.conbuildmat.2020.119844
8. Meng Y., Lifeng L., Bida P., Doo-Yeol Y., Huihui L., Cong Z. A critical review on shear performance of joints in precast Ultra-High-Performance Concrete (UHPC) segmental bridges. Engineering Structures. 2024. 301. DOI: https://doi.org/10.1016/j.engstruct.2023.117224
9. Du J., Meng W., Khayat K. H., Bao Y., Guo P., Lyu Z., Abu-Obeidah A., Nassif H., Wang H. New development of ultra-high-performance concrete (UHPC). Composites Part B. 2021. 224. DOI: 10.1016/j.compositesb.2021.109220
10. Mash J.A., Harries K.A, Rogers C. Repair of corroded steel bridge girder end regions using steel, concrete, UHPC and GFRP repair systems. Journal of Constructional Steel Research. 2023. 207. DOI:10.1016/j.jcsr.2023.107975
11. Pukharenko Yu.V., Panteleev D.A., Zhavoronkov M.I. Fibro-Reinforced Concretes for Ductless Laying of Pipelines. Industrial and Civil Engineering. 2024. 3. P. 57 – 62. DOI: 10.33622/0869-7019.2024.03.57-62
12. Shorstova E.S., Klyuev A.V., Klyuev S.V., Garkina I.A. Thin-grounded quartzite sandstone crushing screening in fiber concrete mixture for 3d-printing. Regional architecture and engineering. 2023. 3(56). P. 69 – 76.
13. Yang G., Weng Y., Tian J., Yang Z. 3D printing towards cost-effective design of composite UHPFRC beams: Effects of fiber distribution and orientation on flexural performances and failure mode transition. Engineering Structures. 2025. 336. DOI: 10.1016/j.engstruct.2025.120486
14. Fedyuk R.S., Liseytsev Yu.L., Taskin A.V., Timokhin R.A., Klyuev S.V., Cesar Casagrande. Increasing in impact viscosity of fiber-ash-concrete. Construction Materials and Products. 2020. 3 (6). P. 5 – 16. DOI: 10.34031/2618-7183-2020-3-6-5-16
15. Jabir H.A., Abid S.R., Murali G., Ali S.H., Klyuev S., Fediuk R., Vatin N., Promakhov V., Vasilev Y. Experimental Tests and Reliability Analysis of the Cracking Impact Resistance of UHPFRC. 2020, Fibers. 8(12). 74. DOI: 10.3390/fib8120074
16. Perry V., Eng P. What Really Is Ultra-High Performance Concrete? Towards a Global Definition. Proceedings of the 2ndInternational Conference on Ultra-High Performance Concrete Material & Structures. Fuzhou. 2018.
17. Perry V.H., Seibert P.J. Fifteen years of UHPC construction experience in precast bridges in north America. Proceedings of the RILEM-fib-AFGC Int. Symposium on Ultra-High Performance Fibre-Reinforced Concrete. Marseille. France. 2013.
18. Marchenko M., Chilin I., Selyutin N. Experience in using ultra high performance fiber reinforced concrete elements. Bulletin of Science and Research Center of Construction. 2021. 30 (3). P. 41 – 50. DOI: 10.37538/2226-9696-2021-3(301-61-50
19. Chilin I. Influence of technological factors on the properties of ultra-high-performance fiber reinforced concrete. Bulletin of Science and Research Center of Construction. 2020. 27 (4). P. 135 – 147. DOI: 10.37538/2224-9494-2020-4(27)-135-147
20. Burroughs J.F. Shannon J., Rushing T.S., Yi K., Gutierrez Q.B., Harrelson D.W. Potential of finely ground limestone powder to benefit ultra-high performance concrete mixtures. Construction and Building Materials. 2017. 141. P. 335 – 342. DOI: 10.1016/j.conbuildmat.2017.02.073
21. Li P.P., Brouwers H.J.H., Chen, W., Qingliang, Y. Optimization and characterization of high-volume limestone powder in sustainable ultra-high performance concrete. Construction and Building Materials. 2020. 242. DOI: 10.1016/j.conbuildmat.2020.118112
22. Ferdosian I. Camoes A., Ribeiro M. High-volume fly ash paste for developing Ultra-high performance concrete (UHPC). Ciência & Tecnologia dos Materiais. 2017. 29 (1). P. 157 – 161. DOI: 10.1016/j.ctmat.2016.10.001
23. Yang J., Zeng J., He X. Eco-friendly UHPC prepared from high volume wet-grinded ultrafine GGBS slurry. Construction and Building Materials. 2021. 308. DOI: 10.1016/j.conbuildmat.2021.125057
24. Soliman N.A., Tagnit-Hamou A. Partial substitution of silica fume with fine glass powder in UHPC: Filling the micro gap. Construction and Building Materials. 2017. 139. P. 374 – 383. DOI: 10.1016/j.conbuildmat.2017.02.084
25. Matos A.M., Granja J., Nunes S., Barosso-Aguiar J.L., Azehna M. Hardening characterisation of a non-proprietary and more eco-friendly UHPC. Construction and Building Materials. 2023. 363. DOI: 10.1016/j.conbuildmat.2022.129803
26. Wille K., Kim D.J., Naaman A.E. Strain-hardening UHP-FRC with low fiber contents. Materials and Structures. 2010. 44. P. 583 – 598. DOI:10.1617/s11527-010-9650-4
27. Yoo D.Y., Sohn H.K., Borges P. H.R., Fediuk R., Kim S. Enhancing the tensile performance of ultra-high-performance concrete through strategic use of novel half-hooked steel fibers. Journal of Materials Research and Technology. 2020. 9 (3). P. 2914 – 2925. DOI: 10.1016/j.jmrt.2020.01.042
28. Kang S.H., Kim J.J., Chung Y.S. Effect of sand grain size and sand-to-cement ratio on the interfacial bond strength of steel fibers embedded in mortars. Construction and Building Materials. 2013. 47. P. 1421 – 1430. DOI: 10.1016/j.conbuildmat.2013.06.064
29. Wille K., Loh K.J. Nanoengineering Ultra-High-Performance Concrete with Multiwalled Carbon Nanotubes. Transportation Research Record. 2010. 2142 (1). P. 119 – 126. DOI: 10.3141/2142-18
30. Wille K., Naaman A.E. Effect of Ultra-High-Performance Concrete on Pullout Behavior of High-Strength Brass-Coated Straight Steel Fibers. ACI Materials Journal. 2013. 110. P. 451 – 462.
31. Kim G.W., Oh T., Lee S.K., Banthia N., Yoo D.Y. Development of Ca-rich slag-based ultra-high-performance fiber-reinforced geopolymer concrete (UHP-FRGC): Effect of sand-to-binder ratio. Construction and Building Materials. 2023. 370. DOI: 10.1016/j.conbuildmat.2023.130630
32. Zhou Y., Guo D., Xing F., Guo M. Multiscale mechanical characteristics of ultra-high performance concrete incorporating different particle size ranges of recycled fine aggregate. Construction and Building Materials. 2021. 307. DOI: 10.1016/j.conbuildmat.2021.125131
33. Ibrahim M.A., Farhat M., Issa M.A., Hasse J.A. Effect of Material Constituents on Mechanical and Fracture Mechanics Properties of Ultra-High-Performance Concrete. ACI Materials Journal. 2017. 144. P. 453 – 465. DOI: 10.14359/51689717
34. Matiushin E., Sizyakov I., Svetsova V., Soloviev V. The Properties and Behavior of Ultra-High-Performance Concrete: The Effects of Aggregate Volume Content and Particle Size. Buildings. 2024. 14 (9). 2891.
35. De Larrard F. Concrete Mixture Proportioning A Scientific Approach. London, 1999. 448 p.
36. Luzu B., Trauchessec R., Lecomte A. Packing density of limestone calcined clay binder. Powder Technology. 2022. 408. DOI: 10.1016/j.powtec.2022.117702
37. Soloviev V., Matiushin E., Mihailov V., Efishov L. Effect of mixture flowability on strength and fiber distribution of Ultra High-Performance Fiber Reinforced Concrete. E3S Web of Conferences. 410. DOI: 10.1051/e3sconf/202341001012
38. Abrishambaf A., Pimentel M., Nunes S. A meso-mechanical model to simulate the tensile behaviour of ultra-high performance fiber-reinforced cementitious composites. Composite Structures. 2019. 222. DOI: 10.1016/j.compstruct.2019.110911
39. Soloviev V.G., Matiushin E.V., Veselov V.K. A study of the impact of aggregate type and volume content on the properties of ultra-high performance fine-grained concrete. Technique and technology of silicates. 2022. 29(4). P. 317 – 325.
40. Tasdemir M.A., Karihaloo B.L. Effect of Type and Volume Fraction of Aggregate on the Fracture Properties of Concrete. Fracture Mechanics of Concrete Structures. 2001. P. 123 – 129.
41. Stock A.F., Hannant D.J. and Williams R.I.T. The effect of aggregate concentration upon the strength and modulus of elasticity of concrete. Magazine of Concrete Research. 1979. 31(109). P. 225 – 234.
42. Li V.C. A simplified micromechanical model of compressive strength of fiber-reinforced cementitious composites. Cement and Concrete Composites. 1992. 14 (2). P. 131 – 141. DOI: 10.1016/0958-9465(92)90006-H.
43. Benson S.D.P., Karihaloo B.L. CARDIFRC® – Development and Mechanical Properties. Part III: Uniaxial Tensile Response and Other Mechanical Properties. Magazine of Concrete Research. 2005. 57 (8). P. 433 – 443. DOI: 10.1680/macr.2005.57.8.433
44. Matiushin E.V., Soloviev V.G. Influence of aggregate on the bond strength of corrugated steel fiber with ultra-high performance concrete. Bulletin of BSTU named after V.G. Shukhov. 2025. 4. P. 8 – 26. DOI: 10.34031/2071-7318-2024-10-4-8-26
45. Soloviev V., Matiushin E. A methodology of ultra high performance concrete mix design with a given flowability. Technique and technology of silicates. 2020. 27 (4). P. 107 – 113.
46. Mu R., Chen J., Diao C., Wang X., Qing L. Effect of the orientation of steel fiber on the strength of ultra-high-performance concrete (UHPC). Construction and Building Materials. 2023. 406. DOI: 10.1016/j.conbuildmat.2023.133431
Matiushin E.V., Soloviev V.G. Role of aggregate characteristics in controlling the mechanical properties of Ultra-High Performance Fiber-Reinforced Concrete. Construction Materials and Products. 2026. 9 (5). 4. https://doi.org/10.58224/2618-7183-2026-9-5-4