English English

Keywords: protective-decorative coatings

VITREOUS PROTECTIVE AND DECORATIVE COVERINGS ON WOOD PARTICLE BOARD

https://doi.org/10.34031/2618-7183-2018-1-4-4-12
, , , ,
 4-12 p.
Abstract
Scientific and technological bases of receiving vitreous coverings on wood with use of a torch of low-temperature plasma are developed. Before plasma dusting of glass powders by grain structure 60-120mkm, the special protective coating protecting chipboard from destruction at high-temperature influence of a plasma stream on a front surface of the wood particle board (WPB) was applied. The structure of an intermediate protective coating including mix of a fine-grained glass powder and liquid glass is developed. Preliminary drawing an intermediate protective layer provides several consecutive technological operations.
For receiving vitreous coverings fight of colored and colourless glass are used which was previously ground in spherical porcelain mills. Optimum process parameters of plasma dusting of glass powder on the front surface of chipboard are developed. Optimum parameters of plasma melting is: current - 800A; operating voltage – 30B, a consumption of plasma-forming gas of argon 2m3/h.
Operational and aesthetic-consumer properties of vitreous protective and decorative coverings are investigated. It is established that vitreous protective and decorative coverings have the high durability of coupling with an intermediate protective layer. The received vitreous protective and decorative coverings on the basis of colored and colourless glass have the high water resistance, acid resistance, alkali resistance, as well as microhardness and high aesthetic performance.
The technology is recommended for widespread industrial introduction.
PDF

INVESTIGATION OF INFLUENCE OF PLASMOCHEMICAL MODIFICATION ON MACRO- AND MICROSTRUCTURE OF SURFACE LAYER OF AUTOCLAVE WALL MATERIALS

https://doi.org/10.34031/2618-7183-2018-1-2-4-10
, , ,
 4-10 p.
Abstract
Studies of the high-temperature effect of a plasma torch on the formation of a multilayer structure of the protective and decorative coating of autoclave wall materials are presented. The tasks of the work included studies: a temperature gradient in a multilayer protective-decorative coating; chemical composition of the fused, intermediate and deep layers of the protective and decorative coating; influence of sodium liquid glass on the formation of macro- and microstructures of protective and decorative coatings under the influence of plasma; processes of thermal diffusion and redistribution of oxides in the fused, intermediate and deep layers.
It was found that when the plasma torch was treated with autoclave wall materials, the surface layer was heated to a depth of 3000 μm, and the maximum surface temperature reached 2000 °C. The pattern of the change in the structure of the fused and intermediate layer is revealed. It is shown that the preliminary impregnation of the surface of silica brick during plasma treatment due to the formation of a low-melting melt eliminates microcracks in its deep layers, and high plasma temperatures promote intensive evaporation of sodium and calcium oxides from the fused layer.
PDF

PLASMOCHEMICAL MODIFICATION OF WALL BUILDING MATERIALS

https://doi.org/10.34031/2618-7183-2018-1-2-11-18
, , , ,
 11-18 p.
Abstract
The aim of the work is to study the effect of a high-temperature plasma torch on the processes of phase transformations and layer-by-layer modification of the protective and decorative coating on concrete using as a filler a mixture of quartz sand and hollow glass microspheres. The main tasks included: investigation of the processes of evaporation and thermal diffusion of oxides of plasma-coated coatings; study of phase transformations in the melt and its subsequent crystallization in the process of rapid spontaneous cooling of the fused protective and decorative coating; study of the effect of sodium liquid glass on the processes of polymorphic transformations of alumina and the formation of micro-wicks due to the intense diffusion of sodium oxide; study of operational characteristics of protective and decorative coatings. It was established that the initial phases in the protective-decorative coating are α-Al2O3 and CaO∙6Al2O3 (β-Al2O3), and the liquid sodium glass in the coating leads additionally to the formation of Na2O∙11Al2O3. The top layer of the protective and decorative coating is Na–Ca–Al–Si glass with regions of heterogeneities containing an increased content of sodium oxide. The content of aluminum oxide in the protective and decorative coating based on the battle of high-alumina refractory was 95.1 %. The introduction into the coating composition of sodium liquid glass minimizes the processes of dehydration of the binding component and changes the chemical composition of the protective and decorative coating. Reduction of the aluminum oxide content to 83.0 % affects the microhardness indicators. Microhardness of the concrete surface due to the introduction of liquid glass is reduced from 2510 HV to 887 HV.
PDF