This study investigates ceramic facing materials based on Shomishkul kaolin, Berkutau basalt, and Tabakkum dune sand, with particular emphasis on lowering the peak firing temperature as a practical route to improving production energy efficiency. The fluxing behavior of Berkutau basalt was compared with that of Kazgansay feldspar. The chemical composition of the raw materials, onset and completion temperatures of melting, shrinkage, water absorption, flexural strength, frost resistance, phase composition, and microstructure were evaluated. The total Na2O+K2O content of Berkutau basalt is 12.07 wt.%, which is comparable to that of Kazgansay feldspar (12.95 wt.%); however, the basalt contains substantially higher amounts of Fe2O3 and CaO. The onset and completion temperatures of melting for the raw basalt are 1093 and 1165 °C, respectively, compared with 1380 and 1400 °C for feldspar. At an additive content of 30 wt.%, the onset of melting is 1195 °C for the kaolin-basalt composition and 1361 °C for the kaolin-feldspar system. The optimized KBP-20 to KBP-22 compositions fired at 1100 °C exhibit water absorption of 7.3-8.4%, shrinkage of 3.4-4.5%, and flexural strength of 17.6-19.4 MPa. Increasing the firing temperature to 1150 °C does not substantially improve the principal physical and mechanical properties and is accompanied by increased overall shrinkage. The results support the use of Berkutau basalt as a natural fluxing component and indicate that the peak firing temperature can be reduced by approximately 40-50 °C relative to a conventional feldspar-containing ceramic body. This provides a clear technological basis for reducing kiln thermal demand and improving production energy efficiency.
1. Garzón E., Pérez-Villarejo L., Eliche-Quesada D., Martínez-Martínez S., Sánchez-Soto P.J. Vitrification rate and estimation of the optimum firing conditions of ceramic materials from raw clays: A review. Ceramics International. 2022. 48 (11). P. 15889 – 15898. DOI: 10.1016/j.ceramint.2022.02.129
2. Cengizler H. Effect of calcination temperature on use of high-boron-content waste for low-temperature wall tile production. Ceramics International. 2022. 48 (5). P. 6024 – 6036. DOI: 10.1016/j.ceramint.2021.11.138
3. Bahtli T., Erdem Y. The use of foundry waste sand from investment casting in the production of porcelain tiles. Ceramics International. 2022. 48 (19). P. 27967 – 27972. DOI: 10.1016/j.ceramint.2022.06.100
4. Alonso-De la Garza D.A., Guzman A.M., Gómez Rodriguez C., Martínez D.I., et al. Influence of Al₂O₃ and SiO₂ nanoparticles addition on the microstructure and mechano-physical properties of ceramic tiles. Ceramics International. 2022. 48. P. 12712 – 12720. DOI: 10.1016/j.ceramint.2022.01.140
5. Gao X., Feng X., Zhang D., Zhang J., Peng Y., Pan Z., et al. Synthesis of high-performance mullite ceramics based on associated rare-earth kaolin. International Journal of Applied Ceramic Technology. 2023. 20. P. 1535 – 1546. DOI: 10.1111/ijac.14311
6. De Noni Jr. A., Canever S.B., Henrique P., Silva R.R. Microstructure-oriented porcelain stoneware tile composition design. Ceramics International. 2023. 49. P. 24558 – 24565. DOI: 10.1016/j.ceramint.2022.11.067
7. Ding K., Li A., Lv J., Gu F. Decarbonizing ceramic industry: Technological routes and cost assessment. Journal of Cleaner Production. 2023. 419. P. 138278. DOI: 10.1016/j.jclepro.2023.138278
8. Altimari F., Andreola F., Lancellotti I., Barbieri L. Comparative study of technological behavior of German ball clay and Italian kaolinitic clay in unconventional porcelain stoneware body. Applied Clay Science. 2024. 255. P. 107417. DOI: 10.1016/j.clay.2024.107417
9. Belfiore C.M., Parisi S., Menta S., Mazzoleni P. Use of volcanic ash and chamotte as substitute temper in the production of ceramic tiles. Applied Clay Science. 2024. 262. P. 107603. DOI: 10.1016/j.clay.2024.107603
10. Arkame Y., Harrati A., Imgirne A., Moustapha A., Et-Tayea Y., Yamari I., Sdiri A., El Bouari A., Sadik C. Evaluation and application of Moroccan clay materials in ceramic tiles: Composition and technological behavior. Open Ceramics. 2024. 18. P. 100591. DOI: 10.1016/j.oceram.2024.100591
11. Sadli N., May A., Hamidouche M., Henniche A., Belhouchet H., Boudouh H. Investigations on kaolin mixtures: Impact on mullite formation kinetics and microstructure evolution. International Journal of Applied Ceramic Technology. 2024. 21. P. 3950 – 3966. DOI: 10.1111/ijac.14820
12. Alves C.L., Skorych V., De Noni A. Jr., Hotza D., Gómez González S.Y., Heinrich S. Optimizing raw material composition to increase sustainability in porcelain tile production: A simulation-based approach. Journal of the American Ceramic Society. 2024. 107 (4). P. 2110 – 2127. DOI: 10.1111/jace.19581
13. Gao X., Zhang D., Feng X., Zhang J., Peng Y., Pan Z., et al. Effect of particle size of associated rare earth kaolin powder on the sintering and properties of synthetic mullite. Journal of the American Ceramic Society. 2024. 107. P. 2658 – 2667. DOI: 10.1111/jace.19562
14. Eminov A.M., Kalbaev B.A. Basalt Rocks of Karakalpakstan for Ceramic Production. Refractories and Industrial Ceramics. 2024. 64 (6). P. 571 – 575. DOI: 10.1007/s11148-024-00892-8
15. Wang Y., Zhang J., Gao J., Yang Z. Modification of liquid phase and microstructure of sintered mullite by different additives. International Journal of Applied Ceramic Technology. 2025. 22 (1). P. e14860. DOI: 10.1111/ijac.14860
16. Sokolar R., Nguyen M., Vsiansky D., Pavelka O., Trnik A. The effect of wollastonite on sintering of anorthite ceramic body based on illite-smectite clay and kaolin. Applied Clay Science. 2025. 270. P. 107774. DOI: 10.1016/j.clay.2025.107774
17. Wang S., Chen W., Li X., Qian J., Zhang X., Wang Y. Low-temperature sintering of porcelain tiles at 1100 °C using composite fluxes and their sintering mechanism. Ceramics International. 2025. 51 (6). P. 7087 – 7099. DOI: 10.1016/j.ceramint.2024.12.145
18. Ungureanu A., Sola A., Neri P., Rosa R., Gualtieri A.F., Ferrari A.M. Toward a more reliable evaluation of CO₂ emissions from the firing stage of ceramic tiles within the life cycle assessment (LCA) methodology. Environmental Impact Assessment Review. 2026. 117. P. 108235. DOI: 10.1016/j.eiar.2025.108235
19. Yuan Q., Robert D., Mohajerani A., Tran P., Pramanik B.K. Sustainable ceramic tiles incorporated with waste fly ash from recycled paper production. Journal of Cleaner Production. 2023. 425. P. 138814. DOI: 10.1016/j.jclepro.2023.138814
20. Reaney I.M., Walsh B., Vilarinho P.M. Resource efficiency and energy efficiency (REEE) in the Portuguese ceramic industry: Towards net zero carbon production. Open Ceramics. 2023. 15. P. 100390. DOI: 10.1016/j.oceram.2023.100390
21. Kadyrova Z.R., Purkhanatdinov A.P., Niyazova S.M. Study of Karakalpakstan Bentonite Clay for Producing Ceramic Heat-Insulating Materials. Refractories and Industrial Ceramics. 2021. 61 (5). P. 478 – 480. DOI: 10.1007/s11148-021-00528-1
2. Cengizler H. Effect of calcination temperature on use of high-boron-content waste for low-temperature wall tile production. Ceramics International. 2022. 48 (5). P. 6024 – 6036. DOI: 10.1016/j.ceramint.2021.11.138
3. Bahtli T., Erdem Y. The use of foundry waste sand from investment casting in the production of porcelain tiles. Ceramics International. 2022. 48 (19). P. 27967 – 27972. DOI: 10.1016/j.ceramint.2022.06.100
4. Alonso-De la Garza D.A., Guzman A.M., Gómez Rodriguez C., Martínez D.I., et al. Influence of Al₂O₃ and SiO₂ nanoparticles addition on the microstructure and mechano-physical properties of ceramic tiles. Ceramics International. 2022. 48. P. 12712 – 12720. DOI: 10.1016/j.ceramint.2022.01.140
5. Gao X., Feng X., Zhang D., Zhang J., Peng Y., Pan Z., et al. Synthesis of high-performance mullite ceramics based on associated rare-earth kaolin. International Journal of Applied Ceramic Technology. 2023. 20. P. 1535 – 1546. DOI: 10.1111/ijac.14311
6. De Noni Jr. A., Canever S.B., Henrique P., Silva R.R. Microstructure-oriented porcelain stoneware tile composition design. Ceramics International. 2023. 49. P. 24558 – 24565. DOI: 10.1016/j.ceramint.2022.11.067
7. Ding K., Li A., Lv J., Gu F. Decarbonizing ceramic industry: Technological routes and cost assessment. Journal of Cleaner Production. 2023. 419. P. 138278. DOI: 10.1016/j.jclepro.2023.138278
8. Altimari F., Andreola F., Lancellotti I., Barbieri L. Comparative study of technological behavior of German ball clay and Italian kaolinitic clay in unconventional porcelain stoneware body. Applied Clay Science. 2024. 255. P. 107417. DOI: 10.1016/j.clay.2024.107417
9. Belfiore C.M., Parisi S., Menta S., Mazzoleni P. Use of volcanic ash and chamotte as substitute temper in the production of ceramic tiles. Applied Clay Science. 2024. 262. P. 107603. DOI: 10.1016/j.clay.2024.107603
10. Arkame Y., Harrati A., Imgirne A., Moustapha A., Et-Tayea Y., Yamari I., Sdiri A., El Bouari A., Sadik C. Evaluation and application of Moroccan clay materials in ceramic tiles: Composition and technological behavior. Open Ceramics. 2024. 18. P. 100591. DOI: 10.1016/j.oceram.2024.100591
11. Sadli N., May A., Hamidouche M., Henniche A., Belhouchet H., Boudouh H. Investigations on kaolin mixtures: Impact on mullite formation kinetics and microstructure evolution. International Journal of Applied Ceramic Technology. 2024. 21. P. 3950 – 3966. DOI: 10.1111/ijac.14820
12. Alves C.L., Skorych V., De Noni A. Jr., Hotza D., Gómez González S.Y., Heinrich S. Optimizing raw material composition to increase sustainability in porcelain tile production: A simulation-based approach. Journal of the American Ceramic Society. 2024. 107 (4). P. 2110 – 2127. DOI: 10.1111/jace.19581
13. Gao X., Zhang D., Feng X., Zhang J., Peng Y., Pan Z., et al. Effect of particle size of associated rare earth kaolin powder on the sintering and properties of synthetic mullite. Journal of the American Ceramic Society. 2024. 107. P. 2658 – 2667. DOI: 10.1111/jace.19562
14. Eminov A.M., Kalbaev B.A. Basalt Rocks of Karakalpakstan for Ceramic Production. Refractories and Industrial Ceramics. 2024. 64 (6). P. 571 – 575. DOI: 10.1007/s11148-024-00892-8
15. Wang Y., Zhang J., Gao J., Yang Z. Modification of liquid phase and microstructure of sintered mullite by different additives. International Journal of Applied Ceramic Technology. 2025. 22 (1). P. e14860. DOI: 10.1111/ijac.14860
16. Sokolar R., Nguyen M., Vsiansky D., Pavelka O., Trnik A. The effect of wollastonite on sintering of anorthite ceramic body based on illite-smectite clay and kaolin. Applied Clay Science. 2025. 270. P. 107774. DOI: 10.1016/j.clay.2025.107774
17. Wang S., Chen W., Li X., Qian J., Zhang X., Wang Y. Low-temperature sintering of porcelain tiles at 1100 °C using composite fluxes and their sintering mechanism. Ceramics International. 2025. 51 (6). P. 7087 – 7099. DOI: 10.1016/j.ceramint.2024.12.145
18. Ungureanu A., Sola A., Neri P., Rosa R., Gualtieri A.F., Ferrari A.M. Toward a more reliable evaluation of CO₂ emissions from the firing stage of ceramic tiles within the life cycle assessment (LCA) methodology. Environmental Impact Assessment Review. 2026. 117. P. 108235. DOI: 10.1016/j.eiar.2025.108235
19. Yuan Q., Robert D., Mohajerani A., Tran P., Pramanik B.K. Sustainable ceramic tiles incorporated with waste fly ash from recycled paper production. Journal of Cleaner Production. 2023. 425. P. 138814. DOI: 10.1016/j.jclepro.2023.138814
20. Reaney I.M., Walsh B., Vilarinho P.M. Resource efficiency and energy efficiency (REEE) in the Portuguese ceramic industry: Towards net zero carbon production. Open Ceramics. 2023. 15. P. 100390. DOI: 10.1016/j.oceram.2023.100390
21. Kadyrova Z.R., Purkhanatdinov A.P., Niyazova S.M. Study of Karakalpakstan Bentonite Clay for Producing Ceramic Heat-Insulating Materials. Refractories and Industrial Ceramics. 2021. 61 (5). P. 478 – 480. DOI: 10.1007/s11148-021-00528-1
Kalbaev B.A., Purkhanatdinov A.P., Éminov A.M., Tanatarov O.R., Erejepova J.U., Bekmuratova N.A., Khojabergenov B.M., Ayapbergenov N.X. Energy-efficient building ceramics with reduced firing temperature based on shomishkul kaolin and berkutau basalt. Construction Materials and Products. 2026. 9 (5). 8. https://doi.org/10.58224/2618-7183-2026-9-5-8

English
Русский